GIF89a; EcchiShell v1.0
//proc/self/root//proc/self/root/SAR-->PHY-->line--> ... */ #define __ATM_LM_NONE 0 /* no loop back ^ ^ ^ ^ */ #define __ATM_LM_AAL 1 /* loop back PDUs --' | | | */ #define __ATM_LM_ATM 2 /* loop back ATM cells ---' | | */ /* RESERVED 4 loop back on PHY side ---' */ #define __ATM_LM_PHY 8 /* loop back bits (digital) ----' | */ #define __ATM_LM_ANALOG 16 /* loop back the analog signal --------' */ /* Direction of loopback */ #define __ATM_LM_MKLOC(n) ((n)) /* Local (i.e. loop TX to RX) */ #define __ATM_LM_MKRMT(n) ((n) << 8) /* Remote (i.e. loop RX to TX) */ #define __ATM_LM_XTLOC(n) ((n) & 0xff) #define __ATM_LM_XTRMT(n) (((n) >> 8) & 0xff) #define ATM_LM_NONE 0 /* no loopback */ #define ATM_LM_LOC_AAL __ATM_LM_MKLOC(__ATM_LM_AAL) #define ATM_LM_LOC_ATM __ATM_LM_MKLOC(__ATM_LM_ATM) #define ATM_LM_LOC_PHY __ATM_LM_MKLOC(__ATM_LM_PHY) #define ATM_LM_LOC_ANALOG __ATM_LM_MKLOC(__ATM_LM_ANALOG) #define ATM_LM_RMT_AAL __ATM_LM_MKRMT(__ATM_LM_AAL) #define ATM_LM_RMT_ATM __ATM_LM_MKRMT(__ATM_LM_ATM) #define ATM_LM_RMT_PHY __ATM_LM_MKRMT(__ATM_LM_PHY) #define ATM_LM_RMT_ANALOG __ATM_LM_MKRMT(__ATM_LM_ANALOG) /* * Note: ATM_LM_LOC_* and ATM_LM_RMT_* can be combined, provided that * __ATM_LM_XTLOC(x) <= __ATM_LM_XTRMT(x) */ struct atm_iobuf { int length; void *buffer; }; /* for ATM_GETCIRANGE / ATM_SETCIRANGE */ #define ATM_CI_MAX -1 /* use maximum range of VPI/VCI */ struct atm_cirange { signed char vpi_bits; /* 1..8, ATM_CI_MAX (-1) for maximum */ signed char vci_bits; /* 1..16, ATM_CI_MAX (-1) for maximum */ }; /* for ATM_SETSC; actually taken from the ATM_VF number space */ #define ATM_SC_RX 1024 /* enable RX single-copy */ #define ATM_SC_TX 2048 /* enable TX single-copy */ #define ATM_BACKLOG_DEFAULT 32 /* if we get more, we're likely to time out anyway */ /* MF: change_qos (Modify) flags */ #define ATM_MF_IMMED 1 /* Block until change is effective */ #define ATM_MF_INC_RSV 2 /* Change reservation on increase */ #define ATM_MF_INC_SHP 4 /* Change shaping on increase */ #define ATM_MF_DEC_RSV 8 /* Change reservation on decrease */ #define ATM_MF_DEC_SHP 16 /* Change shaping on decrease */ #define ATM_MF_BWD 32 /* Set the backward direction parameters */ #define ATM_MF_SET (ATM_MF_INC_RSV | ATM_MF_INC_SHP | ATM_MF_DEC_RSV | \ ATM_MF_DEC_SHP | ATM_MF_BWD) /* * ATM_VS_* are used to express VC state in a human-friendly way. */ #define ATM_VS_IDLE 0 /* VC is not used */ #define ATM_VS_CONNECTED 1 /* VC is connected */ #define ATM_VS_CLOSING 2 /* VC is closing */ #define ATM_VS_LISTEN 3 /* VC is listening for incoming setups */ #define ATM_VS_INUSE 4 /* VC is in use (registered with atmsigd) */ #define ATM_VS_BOUND 5 /* VC is bound */ #define ATM_VS2TXT_MAP \ "IDLE", "CONNECTED", "CLOSING", "LISTEN", "INUSE", "BOUND" #define ATM_VF2TXT_MAP \ "ADDR", "READY", "PARTIAL", "REGIS", \ "RELEASED", "HASQOS", "LISTEN", "META", \ "256", "512", "1024", "2048", \ "SESSION", "HASSAP", "BOUND", "CLOSE" #endif /* LINUX_ATMDEV_H */